May 06, 2018 · Linksys WAP54g v.2 dd-wrt Repeater Setup | dd-wrt كـ ربيتر باستخدام السوفت WAP54g إعداد راوتر - Duration: 7:45. Networking 4 All – احتراف الشبكات
Jul 19, 2012 · I got a Linksys WRT54GL v1.1 router that somewhat worked and somewhat didn't: it booted alright (no led errors), responded to ping on its default IP (192.168.1.1), bot other than that, it did not respond on the web interface, nor telnet/ssh, nor dhcp. I tried the 30/30/30 reset , tried TFTP recovery - nothing worked. As it had the original Linksys firmware, at this point it was either a My !free! made in China router have this functionality. And yet I have been banging my head with this new reasonably expensive wireless router from Linksys. Anyway I lug my notebook around. I need my home router to be able to automatically configure notebook IP address using DHCP. At the same time I I recently placed a WRT54GL in my network because my BEFSR41 bricked during a firmware upgrade (none of the known fixes worked, i.e., hard reset, etc.). The questions I have are: 1. I've always used very strong passwords, randomly generated with a password generator and often manually 'toughene Nov 12, 2019 · If 192.168.1.1 isn't the IP address that's configured for the router, it's less of an issue than if the default password isn't correct. The router doesn't need to be reset to find its IP address. Assuming the Linksys WRT54G has been working as your router, you probably have several devices that are connected to it. Hardware: Cisco WRT54GL v1.1 with DD-WRT firmware dd-wrt.v24_std_generic.bin. SNMP enabled on the router and I can successfully telnet into the router using PuTTY. CatTools Device Information: Device Type: Cisco.Router.General Group: Default Name: Cisco Router 1 Host Address: 192.168.1.1 File Na
Forum discussion: Just bought a WRT54GL V 1.1 CL7B. They also had a newer WRT54GL V 1.1 which may have been CO61, at least the unusually helpful sales person said it was newer and he seemed to
Get help with WRT54GL Downloads. The hardware version is located beside or beneath the model number and is labeled version, ver. or V. Techdata: Linksys WRT54GL 1.0, 1.1 This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram. DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version (18.06 or later) onto it! Linksys WRT54GL version 1.1 Close-up of the circuit board Linksys released the WRT54GL (the best-selling router of all time [13] [14] [15] ) in 2005 to support third-party firmware based on Linux , after the original WRT54G line was switched from Linux to VxWorks , starting with version 5. I bought my WRT54GL (1.1) around 2008 and later I order one for my parents, sister and some of my friends has the same device. The router is good as it is but as most of you knows the good hardware is the best with one of the Linux based firmware, at least this is my experience.
Forum discussion: I have acquired a couple of WRT54GL v 1.1 routers. Both exhibit the same problem. I cannot get an ethernet connection to work. I suspect the routers have been setup in some way
Hardware: Cisco WRT54GL v1.1 with DD-WRT firmware dd-wrt.v24_std_generic.bin. SNMP enabled on the router and I can successfully telnet into the router using PuTTY. CatTools Device Information: Device Type: Cisco.Router.General Group: Default Name: Cisco Router 1 Host Address: 192.168.1.1 File Na